If you already have the door, hanging it is a labour-only job, and there is no single flat rate for it in Ireland. The price depends on the door, the frame it is going into, and how much trimming and hardware work is involved, which is why a good fitter quotes after seeing or measuring the opening rather than naming a figure blind.
That short answer raises better questions. What exactly are you paying for when a fitter hangs a door? Why does one door cost more to hang than a full house of doors? And at what point does supply and fit work out better value than buying doors yourself and paying labour on top? This guide answers each one using the same prices and process we work to every week across Meath, Louth and North Dublin.
Quick Answer: What Decides the Cost of Hanging a Door
| Question | Answer |
|---|---|
| Is there a standard rate to hang one door? | No. Labour is quoted per job once the door, frame and floor levels are known. |
| What is included in a proper hanging job? | Removing the old door, trimming, hinge recesses, hanging, latch and handle fitting, adjustment, clean up. |
| Why is one door dearer per door than many? | Travel, set up and protection time are the same for one door as for a full house. |
| Who supplies handles and hinges on a labour-only job? | Usually you do, unless your fitter agrees otherwise. Agree it before the day. |
| When is supply and fit better value? | When you need several doors, new frames, or matched handles and architraves included. |
What a Proper Door Hanging Job Actually Includes
Hanging a door is not just screwing on two hinges. A proper labour-only fitting job covers:
- Removing the old door, hinges and handle without damaging the frame
- Checking the frame is square and the opening is true
- Trimming the new door to the opening, allowing for floor coverings and clearance
- Sealing any trimmed edge, which matters most on pre-finished doors
- Cutting hinge recesses into the door and frame so the door sits flush
- Hanging the door and checking the swing and the gaps all round
- Fitting the latch, strike plate and handle, and adjusting until the door clicks shut cleanly
- Planing or easing any high spots, then cleaning up packaging and offcuts
If a labour quote only says fitting, ask which of these are included. The cheapest quote can stop being cheap if handles, disposal of the old door, or a return visit for adjustment are added later.
Why Labour Quotes Vary So Much
The door itself
A light hollow core door is quick to trim and hang. A solid core or glazed door is heavier, needs two people for safe handling, and takes more care when trimming so the finish and the glass are not damaged. Heavier doors can also need three hinges instead of two.
The frame it is going into
A square, sound frame in a modern estate home is the fastest job there is. Older Irish homes often have frames that are slightly twisted or out of level, and every millimetre of twist has to be worked around at the door. If the frame is rotten or badly damaged, hanging a new door into it is a false economy. Our guide to replacing internal doors without replacing frames explains when a frame can stay and when it should go.
Floors and clearance
New flooring is the most common surprise on a hanging job. Thick laminate, tiles or carpet laid after the old door was fitted can leave too little clearance, so the door needs more trimming, and on some doors there is a limit to how much can come off the bottom rail before the core is exposed.
Hardware
Fitting a simple latch and lever handle is standard work. Privacy locks for bathrooms, door closers, and reusing old handles on a new door all add time. On a labour-only job the handles, hinges and latch are normally supplied by you, so have them on site before the fitter arrives or the job can stall.
One Door or a Full House: Why the Per Door Price Changes
Fitters price in the fixed time around the job as well as the hanging itself: travelling to your home, protecting floors, setting up tools and cleaning up afterwards. That fixed time is nearly the same for one door as it is for eight.
So a single door usually carries the highest labour cost per door. On a full house job, that fixed time is spread across every door, the fitter settles into a rhythm in one home, and the per door labour falls. This is also why our full internal door fitting cost guide shows full house totals rather than one misleading per door figure.
Labour Only or Supply and Fit: Which Works Out Better?
Labour only makes sense when:
- You have one or two doors, already bought, in standard sizes
- Your frames are sound and square
- You are happy choosing and supplying handles, hinges and latches yourself
- You have checked the door can be trimmed to your opening
Supply and fit usually works out better when:
- You need several doors and want them all matching
- Frames, liners or architraves need replacing as well
- You want handles, locks, hinges, liners and architraves included rather than sourced one by one
- You want one team responsible for measuring, the door, and the finished result
For comparison, the doors on our own range run from €199 for the White Primed 2 Panel to €385 to €495 for pre-finished oak and white oak, and every door we supply comes with frame liners, architraves, locks, handles and hinges included. You can browse the full internal door range with prices shown for every model.
What to Check Before You Book a Fitter
- Confirm whether the quote includes handles, hinges and latch fitting, or labour only in the strict sense.
- Ask who takes away the old door and the packaging.
- Check the door can be trimmed to your opening, especially if it is a non-standard size or a glazed model.
- Ask what happens if the frame turns out to be rotten or twisted once the old door comes off.
- Get the finished price in writing before the day, not an estimate that grows on site.
How Our Fitting Service Works
When East Coast Doors supplies and fits your doors, it starts with a free home measure. We measure every opening, check every frame, talk through finishes and hardware, and give you a written quote with fitting priced for your job. On fitting day our own team hangs, adjusts and finishes every door, usually completing a full house in one day. Read more about our internal door installation service.
If you already have doors and only need a price for the whole job done properly, measuring first is still the safest way to get an exact figure. Call 083 814 7923 or use our contact page to book your free home measure.
Frequently Asked Questions
How much does it cost to hang a door in Ireland?
There is no single flat rate. Labour is quoted per job because the door weight, the frame condition, floor clearance and hardware all change the time involved. A written quote after a measure or a clear description of the opening is the only way to get an exact figure.
Why is hanging one door expensive compared with a full house?
The fixed time around the job, travel, set up, floor protection and clean up, is the same for one door as for many. On a full house job that time is shared across all the doors, so the labour cost per door drops.
Do I need to supply handles and hinges for a labour-only job?
Usually yes. On a labour-only booking the fitter brings tools and labour, and you supply the door, hinges, latch and handles unless you agree otherwise in advance. When East Coast Doors supplies the door, liners, architraves, locks, handles and hinges are included.
Can any door be trimmed to fit my opening?
Most doors allow some trimming, but the amount varies. Glazed and pre-finished doors have limits, and older Irish homes often have non-standard openings. Measuring the opening before you buy avoids the most common mistake.
How long does it take to hang an internal door?
A straightforward door in a sound, square frame is the quickest job. Twisted frames, new flooring and heavier glazed or solid doors all add time. A full house of 8 to 10 doors is normally fitted in one day by our own team.
Is it cheaper to hang doors myself?
It can be, if you have the tools and the door is light and standard sized. The risks are over trimming, damaged pre-finished edges, and doors that swing or will not latch. Heavy glazed and solid core doors are the ones most often regretted as DIY jobs.
